Black sticky stuff and rubber gloves

Week 2 and phoned GBS to see if any of my back order items where in stock yet, and yes a few ! more important was the "black sticky bond stuff" was in stock, Jumped into the car, along with the bent bolts from last week and headed over to the factory. As usual when I arrived was offered a cuppa.... always goes down well ! This time Will sorted me out in the stores, swapped the bolts for straight ones, got 3 tubes of the black bond, a couple of brake discs and pads and 2 ball ends. While I was there a quick visit into the workshop to make sure I was doing things right, Craig spent a good 30 minutes going through the next stage of the the build with me, with another few good tips. Unfortunately for me I have to take part of the rear wishbone assembly apart to get a couple of washers in, This can be an IVA fail, so better to sort it out now instead of later which would involve more work.

So back to the build, time to bond and rivet the rear seat panel on, already drilled and temporary in place from last week, Alex and myself removed the panel and put a good bead of bond around the frame and over the rivet holes, its really a 2 man job to make it easy, and a couple of minutes later the panel was back in place, stuck to the bond, located about a dozen rivets around the panel to make sure it was in the right place and started riveting. 15 minutes later, one back seat panel in place and riveted. Clamps placed on the 2 side parts as I was unable to get a drill in for rivets, but this black bonding stuff is pretty strong anyway, give it overnight to cure.

Now onto the front foot well panels, drilled, bonded and riveted.

Alex riveting, learning new skills every weekend !

 



 



Time for a break, and F1 qualifying is on. Also give time for the bond to go off, got about 40 to 60 minute working time with the bond and anywhere between 24 and 48 hours curing time.

 

Top tip... When using the black bonding sticky stuff, use rubber gloves, or something similar, its taken several washes with a good hand cleanser, 2 showers, and a scrub with white spirit to try and get it off my hands and its still not off !!

 

Managed to get it in my hair as well, and on my clothes... bloody stuff gets everywhere !

 

The side foot well panels need a bit of bending so in the "Workmate" Alex clamped the panel and gave it a bend. first time, and a perfect fit !

Before we set this panel in with bond and rivets, we'll put the gearbox mount in while we have space to work round, a bit of trimming with the angle grinder and 4 holes drilled and its in place centrally.

 

 

 

The wiring loom was also placed in an approximate position, screwed to a piece of wood and clamped to where it will be placed on the scuttle (give or take a few Cm's). Brake master cylinder was also bolted in place ready for the brake lines.

 





 

Every time I seem to bend over the frame, reach for something, or even walk past it, I catch the "black sticky stuff" its getting everywhere, so I'm going to stop for a while and go and watch the last race of the F1 series.

 

 Build so far this week,
Rear seat panel finished... 1 hr
Front foot wells, bond and rivets... 3 hrs (2hrs with Alex)
Wiring loom... 0.5hrs
Gearbox mount, trimmed and drilled... 1 hr
master cylinder... 0.25 hr
Scrubbing time...1 hr and still not got the black stuff off !
Total time this week... 6 hrs

Total build time 19 hours
days so far 16
 

 



Rear Wishbones and Handbrake

Not much work during the week, Wife working away, boys and house to look after, and my right arm playing up again, Hospital and Doctors appointments. Bit frustrating as this was an opportunity to lock myself away in the garage and knuckle down to some building without interruptions ? However time was spent doing some research, visiting GBS, and collecting more tools from a friend who has kindly lent me an air riveter, saving me time and effort with my arm.

Fitting the bushes into the rear wishbones... a very tight fit, used a bit of grease and a vice, 28 bushes later... time for a cuppa.

Crush tubes for rear wishbones... fitting same as the bushes... 14 tubes later... another cuppa !!

Trial fit of the upper rear wishbones highlighted a small problem, the bolts supplied seem to be about 5mm to long, and are hitting the frame, Spoke to GBS and they say they should be OK, could pack out with a few washers ? or cut off 5mm of the bolt, tried packing with washers... looks ugly ! so too the grinder and just took off 5mm, redressed with a 10mm die and it now looks "spot on" still with 2 to 3 threads passed the nylock nut.

This only applied to the upper rear front bolts, the bolt for the back of the upper rear was fine and needed no adjustment, photo shows bolt before trimming.

Found fitting the wishbones with the washers very tight, Spoke to Ben at GBS and said to try and get the washers in if I can, If I can see light between the bushes and the brackets then it needs a washer, don't want any "play" in the wishbone setup. A couple of washers where very tight but a small screwdriver and a small "tapping stick" made sure no light was showing.

So rear wishbones all lightly bolted up, not tightening fully, just in case things have to come off, Rear dampers and springs fitted and again lightly bolted up, also rear hub carriers fitted to upper wishbones.

Problem 2 ?? while trying to fit the lower rear wishbone to the hub carrier I seem to have bent the long bolt ? only very slightly, can't see the bend, only when I try and fit it I find a tight spot, and on the flat kitchen surface when I roll the bolt you can feel the bend, must only be a fraction of a mm, but its there. So I'll leave that till I get a replacement from GBS on next weeks visit.

 While working at the rear, and I've got the bits to install the handbrake, only 2 nuts and bolts, and a couple of grommet's. Only 30 minutes, 20 of them putting the grommet's in !

That's it today, going for my roast dinner !

So times for the build so far...
Installing the bushes in the wishbones,  3 hrs
fitting crush tubes, 0.5 hr
Fitting wishbones, 2 hrs
Adjusting bolts 0.5 hr
Dampers and springs 0.5 hr
Handbrake 0.5 hr
Total this blog 7 Hours

Total for build... 13 Hours
Days from Start... 9

Picking up the kit

D-Day has finally arrived ! Time to pick up the kit. A short 20 minute drive over to GBS on Friday afternoon, thinking it would only take an hour or so to put everything in the van ended up being just over 3 hours ? This was simply that I had to check every item onto the van and sign it off, and that included every nut, bolt, washer, tie-wrap, panel, engine, etc, plus having instructions from Ben at GBS on how things went together and which items to do first. Unfortunately a few items were out of stock, most due in the next week or so, but I've got plenty of work to do with what I've got already.

Organised a couple of mates to help unload the van on my return, may thanks to the 2 Steve's for the help, only took 20 minutes to unload and stack in the garage !

All in by 7:30pm.

Busy Saturday, so nothing started on the Zero today, had to get a couple of tools from Machine Mart which I had forgotten to get last week, unfortunately the staff at the shop are lacking the information and know how on the simplest tools, a very frustrating morning explaining what a "Deburring" tool was and the difference between UNF and UNC.... 3 members of staff didn't have a clue ??

So Sunday, time to get started, Listening to GBS, Back seat panel one of the first things to go in, so measured up, drilled and fixed with temporary rivets. The bonding compound (the black sticky stuff) was one of the items out of stock till next week, so not finished yet, just held in place with temporary rivet's.

TOP TIP : to get the back seat panel in, bend the panel in the middle forming an arc, then drop in the sides. easy with an extra pair of hands and not scraping the powder coating !

Next was to get the steering column bush kit in place, Ben from GBS said "it is a bast**d to get in", and he wasn't wrong !! Fairy liquid everywhere, and even bubbles coming out of my mouth !

 

 

 

Now to get the boys involved ? Using a 7/16" UNF tap, removing the powder coating from the seat belt harness anchor points.

 



 

Thanks boys ! while they where doing that job, I was looking at the next item, the fuel filter, pump, and mounting plate. A first for me, using Rivnuts. Marked out the holes and started drilling, inserted the Rivnuts and set with tool. A Slight mistake... 2 Rivnuts 1mm out when lined up with the holes ? as James would say " Oh Cock" ! Simple fix, just make the holes a little large in the plate, as seen in the photo.

 

 



 Time for tea, So far total build time 6 hours.

One step closer to D-Day !

The Zero frame has just come off the jig... off to the powder coaters now.
Estimated delivery time now next Friday, will have conformation next Wednesday ?

Photos from GBS.


Since the last blog the Motorbike and the boys quad bike have been sold, bit sad to see them go but they are doing nothing sat in the garage, and the space is needed. As a good friend said " A fast £10 is better that a slow £20" !

So the last few preparations to the garage have been completed this morning. Compressed air feed to the garage; simple case of a new air line through the garage wall from the side workshop where the compressor lives, less noise and again more space in the garage. Quick release fittings on all air tools fitted this morning... well done Alex.

6 days and counting !